artisstm, посмотри на темы про потерянные дампы боксов. Дампов мало не бывает. PS Может я и злой. но я бы таким мАСтерАМ дампы бы собирал недели через три после просьбы. Чтобы сами посуетились, побегали, почитали. У меня в облаке ( заметьте - именно в облаке ) лежат все дампы всех сделанных консолей. Свои нервы стоит беречь. PPS Извините, накипело.
у меня дампы всегда надежно хранятся, а те, кто теряют не далекого ума или первый раз делали и не знали на сколько это критично в случае с пс3
Я верю. что нормальные мастера не попадают в такую ситуацию. А таким асам это наука. В мануалах по двнгрейту PS3 это всегда наверху выделенно красным
Все таки послушайте azunai, и сразу паяете линкер, делаю фатку, 3 раза переложил клипсу, паяюсь теперь
а есть у кого-нибудь дамп от 3000й ? пришла тут одна. похоже по софту умерла. хочу попробовать поднять... Код: ****************************** * NOR Dump Tool Version0.9.x * ****************************** DRAFT for 0.9.7 Using byte reverse method ****************************** * Statistics * ****************************** Bytes '00' found 4644949 times, 27.69% Good Bytes 'FF' found 3490942 times, 20.81% Too High Other bytes found 37193 times maximum, 0.22% Good ****************************** * Generic Data * ****************************** Section: metldr blanks of name : read '2E32000000000000000000000000000000000000000000000000' ! mismatch pattern '0000000000000000000000000000000000000000000000000000' ! FAIL Some checking were not successful. You may need to check further your dump. But fortunately for the Generic section of the NOR it may be fixed. ****************************** * Per Console Data * ****************************** Section: mtldr revision : read C36C2E4300AACBE6F64FAD92 Section: mtldr binary size : read 00000F97 Section: mtldr pcn : read D5A463662F12A5319D2A6F0A Section: EID0 - IDPS : read 00000001008C000C1402EEBC102F98B6 Section: EID0 static : read 0012000B Section: EID0 pcn : read D5A463662F12A5319D2A6F0A Section: EID3 - ckp_mgt_id : read 00000000040B260B Section: EID3 static : read 000100D0 Section: EID3 pcn : read D5A463662F12A5319D2A6F0A Section: EID5 - IDPS : read 00000001008C000C1402EEBC102F98B6 Section: EID5 static : read 00120730 Section: EID5 pcn : read D5A463662F12A5319D2A6F0A Section: PS3 MAC Address : read 280DFC9B38F7 Section: cISD1 0001/0002 ? : read 0002 Section: cISD1 - CID : read 0354696A Section: cISD1 - eCID : read 01C500001B09470E140DF44200000010 Section: cISD1 - board_id : read 27460334 Section: cISD1 - kiban_id : read 402133228847 Section: cISD1 -0x3F0A4 Data: read 013301330162 Section: cISD1 -0x3F0B0 Data: read 0002001100020012 Section: cISD1 - ckp_mgt_id : read 00000000040B260B Section: cISD2 - wlan_data1 : read 1FFF000000000000 Section: cISD2 - wlan_data2 : read 0000000000000000 Section: cvtrm - pck/puk : read 47E571A85713A8F88217FE53AC72B7F9CF5D35FE Section: HDD SHA1 SUM : read A2586C03783502E507EE59A750ED9D85E66907B1 Section: HDD information ? : read 00000007 Section: HDD information : read Hitachi HTS543232A7A384 Section: PS3 Serial Number : read E20353330NML8P Section: Bootldr revision : read 2E604104D943D1B534D4C5F5 Section: Bootldr binary size: read 0000300B Section: Bootldr pcn : read D5A463662F12A5319D2A6F0A Data found in NOR to identify the SKU are: TargetID | metldr | bootldr TargetID | Offset0 | Offset1 | Offset0 | Offset1 00 F9B0 0F97 300B 300B No problem found in the Per Console Data, anyway remain careful! ****************************** * Area filled with 00 or FF * ****************************** ' FlashHeader' from '0x00000000' to '0x00000010' is full of '0x00' ! GOOD ' FlashHeader' from '0x00000030' to '0x00000200' is full of '0x00' ! GOOD ' FlashFormat' from '0x00000210' to '0x00000400' is full of '0xFF' ! GOOD 'FlashRegion over' from '0x00000620' to '0x00000800' is full of '0x00' ! GOOD ' asecure_loader' from '0x000101F0' to '0x0002F000' is full of '0x00' ! GOOD ' eEID' from '0x00030DD0' to '0x0003F000' is full of '0xFF' ! GOOD ' cISD' from '0x0003F046' to '0x0003F060' is full of '0xFF' ! GOOD ' cISD' from '0x0003F270' to '0x0003F800' is full of '0xFF' ! GOOD ' cCSD' from '0x0003F820' to '0x0003F850' is full of '0xFF' ! GOOD ' cCSD' from '0x0003F850' to '0x00040000' is full of '0xFF' ! GOOD ' cCSD' from '0x0003F8AC' to '0x0003F8B0' is full of '0xFF' ! GOOD ' trvk_prg0' from '0x000402F0' to '0x00040FF0' is empty (00 / FF) ! GOOD ' trvk_prg0' from '0x00040FF0' to '0x00060000' is empty (00 / FF) ! GOOD ' trvk_prg1' from '0x000602F0' to '0x00060FF0' is empty (00 / FF) ! GOOD ' trvk_prg1' from '0x00060FF0' to '0x00080000' is empty (00 / FF) ! GOOD ' trvk_pkg0' from '0x00080270' to '0x00080FF0' is empty (00 / FF) ! GOOD ' trvk_pkg0' from '0x00080FF0' to '0x000A0000' is empty (00 / FF) ! GOOD ' trvk_pkg1' from '0x000A0270' to '0x000A0FF0' is empty (00 / FF) ! GOOD ' trvk_pkg1' from '0x000A0FF0' to '0x000C0000' is empty (00 / FF) ! GOOD ' ros0' from '0x000C000E' to '0x007C0000' ! FAIL ' ros1' from '0x00D6F49C' to '0x00EC0000' is empty (00 / FF) ! GOOD 'CELL_EXTNOR_AREA' from '0x00F20040' to '0x00F20200' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00F20240' to '0x00F40000' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00F40030' to '0x00F60000' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00F60060' to '0x00F69400' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00F69408' to '0x00F69430' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00F69530' to '0x00F69C00' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00F69C00' to '0x00F7F000' is full of '0xFF' ! GOOD 'CELL_EXTNOR_AREA' from '0x00F80030' to '0x00FA0000' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00FA0060' to '0x00FA9400' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00FA9408' to '0x00FA9430' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00FA9530' to '0x00FA9C00' is full of '0x00' ! GOOD 'CELL_EXTNOR_AREA' from '0x00FA9C00' to '0x00FBF000' is full of '0xFF' ! GOOD 'CELL_EXTNOR_AREA' from '0x00FBF000' to '0x00FC0000' is full of '0xFF' ! GOOD ' bootldr' from '0x00FF00F0' to '0x01000000' is full of '0xFF' ! GOOD Some checking were not successful. You may need to check further your dump. Be cautious there is something fishy in your dump. ****************************** * Not Empty Area * ****************************** ' asecure_loader' from '0x00000840' to '0x000101F0' is not empty ! GOOD ' eEID' from '0x0002F090' to '0x0002FB70' is not empty ! GOOD ' eEID' from '0x0002FB90' to '0x000302A0' is not empty ! GOOD ' eEID' from '0x000302C0' to '0x000303A0' is not empty ! GOOD ' eEID' from '0x000303A0' to '0x000303D0' is not empty ! GOOD ' eEID' from '0x000303F0' to '0x00030DD0' is not empty ! GOOD 'CELL_EXTNOR_AREA' from '0x00F20200' to '0x00F20240' is not empty ! GOOD ' CRL1' from '0x00F40000' to '0x00F40030' is not empty ! GOOD ' DRL1' from '0x00F60000' to '0x00F60060' is not empty ! GOOD ' OCRL0200' from '0x00F69430' to '0x00F69540' is not empty ! GOOD 'CELL_EXTNOR_AREA' from '0x00F7F000' to '0x00F80000' is not empty ! GOOD ' CRL2' from '0x00F80000' to '0x00F80030' is not empty ! GOOD ' DRL2' from '0x00FA0000' to '0x00FA0060' is not empty ! GOOD ' OCRL0200' from '0x00FA9430' to '0x00FA9540' is not empty ! GOOD 'CELL_EXTNOR_AREA' from '0x00FBF000' to '0x00FC0000' is not empty ! GOOD ' bootldr' from '0x00FC0040' to '0x00FF0130' is not empty ! GOOD There are data in supposed areas, anyway remain careful! ****************************** * Per Firmware Data * ****************************** Short MD5 checking for revokation E77B26F129010C77F7A6D0D1FFB906D7 trvk_prg0 unknown but good header ! WARNING E77B26F129010C77F7A6D0D1FFB906D7 trvk_prg1 unknown but good header ! WARNING A43D54210B7DC02DC650880FF9AE6688 trvk_pkg0 unknown but good header ! WARNING A43D54210B7DC02DC650880FF9AE6688 trvk_pkg1 unknown but good header ! WARNING Short MD5 checking for core os 0 files Short MD5 checking for core os 1 files 09A1D434DBD7197E7C3AF8A7C28CA38B 'creserved_0' 9496940BC3CBAB8E06CDB8DA1A8FB0B3 'sdk_version' SDK '3.72' 70CC06C9C4E2B7DEC397425065020BA4 'spu_pkg_rvk_verifier.self' 2EF1679656908524F65926932D85B8B3 'spu_token_processor.self' 93F715DB4499344E72315290A00014D3 'spu_utoken_processor.self' F89EBC0F8270D651D3143A4AAB696B4B 'sc_iso.self' C5038FBA00845CCE9B9E61ECB15DD7B6 'aim_spu_module.self' 1EE8070323E165EA687AAF9FE9002F61 'spp_verifier.self' A71FCC4F3B33B009A21BF44926348694 'mc_iso_spu_module.self' 9EED10FA460DA1731319ADFFAE848455 'me_iso_spu_module.self' 4913B8C9F264BADF81BCD8F53F9257F4 'sv_iso_spu_module.self' D2E97F0C6E2FCDA18F94BC8E9241C90B 'sb_iso_spu_module.self' 066D2A3F7ED4670667B6402FF5F1741C 'me_iso_for_ps2emu.self' 5235E2AD69FB63D311717DE441FF7B6E 'sv_iso_for_ps2emu.self' A88C5BA3789CB5FE569D416D24123FF0 'default.spp' 78E101C6217EDB7E0EAAB48D0EDCE4D2 'lv1.self' CFB561F7322995A899DFE232773CE215 'lv0' 604B42A216E8833936D061AAD16F1E77 'lv0.2' 0A73ABDF1A4525F2C08208368BD0CD3F 'lv2_kernel.self' D274336D5A882EDE851E83353E08FEF2 'eurus_fw.bin' 47C5FC6D298FB7404646561D8B887A5C 'emer_init.self' E2C5D2DCFEE8C83C2B7B4BDCDFAC186F 'hdd_copy.self' B2E08DC15D8C5B836731AE910F63BA19 'manu_info_spu_module.self' 36FC5E86FDE1B59AF91AF0E66CC1542B 'prog.srvk' 540438CA195F4E21FDDF68D6DE273DB7 'pkg.srvk' Some checking were not successful. You may need to check further your dump. Be cautious there is something fishy in your dump. ****************************** * Data Repetition * ****************************** No repetition found on Address '00800000' ! GOOD No repetition found on Address '00400000' ! GOOD No repetition found on Address '00200000' ! GOOD No repetition found on Address '00100000' ! GOOD No repetition found on Address '00080000' ! GOOD No repetition found on Address '00040000' ! GOOD No repetition found on Address '00020000' ! GOOD No repetition found on Address '00010000' ! GOOD No repetition found on Address '00008000' ! GOOD No repetition found on Address '00004000' ! GOOD No repetition found on Address '00002000' ! GOOD No repetition found on Address '00001000' ! GOOD No repetition found on Address '00000800' ! GOOD No repetition found on Address '00000400' ! GOOD No repetition found on Address '00000200' ! GOOD No repetition found on Address '00000100' ! GOOD No repetition found on Address '00000080' ! GOOD No repetition found on Address '00000040' ! GOOD No repetition found on Address '00000020' ! GOOD No repetition found on Address '00000010' ! GOOD No repetition found on Address '00000008' ! GOOD No repetition found! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ! 0x005E3D94 or 36.81% of the file has been checked ! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Error in Statistics -You can run again with option -P only Error in Generic Data Checking -You can run again with option -G only Error in 00/FF filled area -You can run again with option -f only Error in Per Firmware data -You can run again with option -F only !!!!!!!!!!!!!!!!!!!!!!!!!!!!! ! FAIL fix it and try again ! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Подключил E3 flasher, хочу обновить вставляю SD карточку с прошивкой (28-10-11.) ноль эмоций не одной голубой лампочки не горит, подключил через микро усб тоже самое. При нажатии на резет, лампочки еле мырг и все.
правильно ли обновляеш?если флешер обновляется то на карте памяти прошивка пропадает,если подключить к компу флешер то должен увидеть диск kirnelbootdisk,если не появляется то пробуй нажимать ресет
Да пробовал, я думаю разницы нет Macos или Windows должен определиться пробовал два кабеля микро усб один от джостиков другой обычный. А с флешки не проподает файлик.
Помойму я приказал своей пс3 вечно жить, припаял линкер, включил пс 3, мне выдал то что он подключен к hdmi, и просит подтверждения, я беру включаю джостик, один включил он не нашел пс 3, другой включил определился, но на кнопки не реагирует, тогда я попробовал подключить проводом джостик, оказалось пс3 висит я отключаю ее, включаю и ни чего не происходит, я отпаиваю линкер протираю спиртиком, смотрю сопли, все чисто, а эффект тот же, включаю, один пик, кулер крутится, а загрузки нет. Это значит я убил память?
возможно при пайки ошибся и что то припаял не так,что то замкнул по ходу, я всегда пишу что лучше прижимать клипсу... а пайка только если есть большой опыт
пробовай подключать клипсу без харда и считывать дамп если не поможет то попробывай как при брике-что я не уверен что поможет
