Вем привет! Моя проблема такова, при попытке собрать nand для freeboot в xebuild столкнулся с такой проблемой. Спойлер: ERROR: you need to specify 1BL key! c:\xeBuild>xebuild -f 17511 -d mydata -t glitch2 -c trinity updflash.bin --------------------------------------------------------------- xeBuild v1.18.800 --------------------------------------------------------------- ---- { Image Build Mode } ---- building glitch2 image ******* ERROR: 1BL key 0x8CFC1DFDCF5C37A52AE427C397A45363 does not appear to be correct! ******* ERROR: 1BL key 0x8CFC1DFDCF5C37A52AE427C397A45363 does not appear to be correct! ERROR: you need to specify 1BL key! --------------------------------------------------------------- Usage : xeBuild [mode] -t <type> [<switch> [<switch>...]] <out.bin> Example : xeBuild -t retail -c trinity -d files -b 0102...0f -p 0102...0f out.bin Switches: -t <type>: retail, jtag, glitch, glitch2, glitch2m, devkit (defaults to retail) -p <key> : 32 character CPU hex key (override, can be elsewhere) -b <key> : 32 character 1BL hex key (override, can be elsewhere) -c <con> : console type -d <dir> : per build files directory -f <dir> : use different data dir and file lists -s <file>: outputs SHA-1 of final image to <file>, if <file> is not provided an auto generated name is used -o <opt> : set xeBuild options -a <name>: append patches -i <ext> : adds _<ext> into firmware ini and patches file names -r <ext> : adds _<ext> into ini bl section name and patches file names -8 <pat> : adds raw patch to NAND just before finalizing -v : shows more info during build process -noenter : suppresses prompt for enter key when finished -? : shows this info legend: [mode] : build, extract, client, update - defaults to build if not present <con> = xenon, zephyr, falcon, jasper, jaspersb, jasper256, jasper512, jasperbb, jasperbigffs, trinity, trinitybb, trinitybigffs corona, corona4g, winchester, winchester4g <dir> = path, absolute or relative, to a directory - do not terminate with / <key> = 128 bit key in hexadecimal representation <name> = name.bin contents will be appended to hv/kernel patches <out.bin> = optional, overrides auto built output image name <ext> = using this option would cause the builder to look for _glitch_<ext>.ini instead of _glitch.ini and patches_jasper_<ext>.bin instead of patches_jasper.bin <opt> various options can be specified on the command line, see perbox sample ini for descriptions listed below, ALL are available to all image types the others can be specified but are only used for that specific image type ALL = nomobile noremap noecdremap nosecurity nosusecurity nandmu smcnocheck cputemp= ALL = gputemp= edramtemp= overcputemp= overgputemp= overedramtemp= cpufan= gpufan= ALL = avregion= gameregion= dvdregion= macid= cfldv= JTAG/GLITCH = smcnoeject smcnoblink cygnos demon xellbutton= xellbutton2= dvdkey= JTAG only = nodvd olddvd dualboot= GLITCH only = patchsmc options noted above with an = are expected to be followed with a value specifying one of the options without an = is the same as setting TRUE in the ini any value assigned to it will be ignored. note that command line options take precedence over any values set in perbox ini and that only values preceded with 0x will be interpreted as hex, MAC is the only exception example: -o macid=00:22:48:F1:01:02;gameregion=0x00FF;nomobile example: -o macid=00:22:48:F1:01:02 -o gameregion=0x00FF -o nomobile example: -o macid=002248F10102 -o gameregion=255 -o nomobile <pat> = optional, <pat> consists of filename.ext,offset patches NAND image with file contents just before combining spare and finalizing ecc offset is the raw offset without spare data file will load based from the -f directory, or absolute path if drive letter is found add 0x to offset to specify hexadecimal, otherwise it will be read as decimal example: -8 myfile.bin,0x12345 example: -8 myfile.bin,0x12345;myotherfile.bin,0x54321 --------------------------------------------------------------- press <enter> to quit... Хотя в Dump Checker все было ок... Консоль Слим, Тринити, дашборд 17511 Помогите пожалуйста собрать nand уже несколько дней вожусь с приставкой... Заранее благодарен!
Через AutoGG 0.9.4 v7 Kernel 17511 удалось собрать образ, пока что все нормально, но теперь запуск долгий, пожалуйста, у кого есть архив с прошивками ПЛИС чипов ПОДЕЛИТЕСЬ ПОЖАЛУЙСТА, особенно под ace v3 нужна.
(обновлённый архив для slim ЗДЕСЬ) ничего не найдено, я уже был на этой странице, перебираю прошивки из RELEASE, но интересен ещё и второй архив который обновленный ля Slim...
Если качал xeBuild отдельным архивом, там нет или неверный ключ 1BL, чтобы не было претензий у MS. Ключ несложно нагуглить. Прописывать в 1bl.txt
Да, качал последний xeBuild. Вот в чем дело... Благодарю за ответ. Маленький вопрос, многие ссылки уже недействительны, где можно все ваши прошивки под чипы скачать?