Вчера прошил приставку Phat с версии 1.91 до 3.0. Были проблемы только со снятием ключа, так как не сразу получилось его снять, с попытки наверное 15-й нормально все записалось, ну и дальше все по маслу пошло. После прошивки я засунул старый диск с игрой и...просто ничего не произошло. На 2 секунды показалась надпись чтение, а потом снова открыть лоток, не читает ни музыку не фильмы. С проводкой все норм, прошилось вроде тоже все отлично. Есть версия что я спалил лазер(прочитал в других темах, но я не знаю как я мог его спалить). Может у кого было и кто нибудь знает решение проблемы(? Привод lite-on и так как даш у меня 13599 то и по инструкции я принял что у меня привод 02510c.
Я шился по местному мануалу ... всё ок. Тож 02510с. Тот же даш сейчас стоит. И с 1.91 на 3.0. Попробуй прошить еще раз . На Лт 2.0 попробуй . ... чем шился и в какую прошу ключ вставлял. Попробуй лиц диск вставить.
Абсолютно все делал по инструкции. Шился JungleFlasher 0.1.91.0. А на lt 2.0 как шиться? Там столько шаблонов я зх что использовать) Лиц. диска у меня нет.
Попробуй выбрать последний Джангл ,хотя я шился не последним. Твой файл прошивки в папке firmware LTPlus-0251-v3.0 . Джангл с файлами прошивки ЛТ 3.0
С час опять пытался прошить привод, но в под самый конец когда нужно жать кнопку Write, привод пропал( раньше тоже так было, через 10 мин программа опять будет видеть привод), попытаюсь прошить еще раз. И вообще это нормально, что от этой программы у меня комп иногда по 5 минут может виснуть, причем намертво? Выложил файлы. Заметил в самом ключе два одинаковых символа. 1B824441DB78985D7369CCFE7BDE83B7 там две одинаковые буквы СС, в инструкции не сказано, но может так не должно быть?
Так, новая проблема. Так как я в прошлый раз не завершил прошивку, так как программа перестала видеть привод. Я понадеялся что это как обычно и через время он снова его увидит. Но время идет и ничего не происходит, кнопка включения постоянно моргает и меня посещают плохие мысли(( все порты перебрал. Перезагрузил несколько раз, и что то ни че( Диски не воспроизводит вообще, ничего, просто пишет "открыть лоток" --- добавлено: Jan 23, 2012 2:50 PM --- лог с самой первой прошивки. Спойлер ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ JungleFlasher 0.1.91 Beta (300) Session Started Sun Jan 22 19:15:26 2012 This is a 32 bit process running on 2 x 32 bit CPUs portio32.sys Driver Installed portio32.sys Driver Started, thanks Schtrom ! Found 4 I/O Ports. Found 1 Com Ports. Found 9 windows drives A: C: D: E: G: K: L: M: N: Found 1 CD/DVD drives G: Drive is Lite-On.. Drive is Lite-On.. Sending Vendor Intro to port 0x01F0 Status 0xD0 Re-sending Vendor Intro: ........................................ Device Intro failed! PhatKey extraction failed! Sending Vendor Intro to port 0x01F0 Status 0x0 Re-sending Vendor Intro: ........................................ Device Intro failed! PhatKey extraction failed! Sending Vendor Intro to port 0x01F0 Status 0x51 Re-sending Vendor Intro: ...................................... Serial flash found with Status 0x52 Stage 2 failed Stage 1 failed Extracted drive key failed Verification ! PhatKey extraction failed! Sending Vendor Intro to port 0x01F0 Status 0x80 Re-sending Vendor Intro: . Serial flash found with Status 0x52 Stage 2 failed Stage 1 failed Extracted drive key failed Verification ! PhatKey extraction failed! Drive is Lite-On.. Drive is Lite-On.. Sending Vendor Intro to port 0x01F0 Status 0xD0 Re-sending Vendor Intro: . Serial flash found with Status 0x52 Stage 1 failed Stage 1 failed Extracted drive key failed Verification ! PhatKey extraction failed! Sending Vendor Intro to port 0x01F0 Status 0x51 Re-sending Vendor Intro: ............. Serial flash found with Status 0x52 Extracted drive key passed Verification ! key returned: 1B824441DB78985D7369CCFE7BDE83B7 Key data saved to C:\Users\SVITCHER\Desktop\Новая папка (4)\Моя прошивка\Key.bin PhatKey files extraction aborted! Sending Vendor Intro to port 0x01F0 Status 0x48 Re-sending Vendor Intro: . Serial flash found with Status 0x52 Stage 1 failed Stage 1 failed Extracted drive key failed Verification ! PhatKey extraction failed! No Drive Detected! DVDkey files extraction aborted! Sending Vendor Intro to port 0x01F0 Status 0x80 Re-sending Vendor Intro: .................. Serial flash found with Status 0x52 Extracted drive key passed Verification ! key returned: 1B824441DB78985D7369CCFE7BDE83B7 Key data saved to C:\Users\SVITCHER\Desktop\Новая папка (4)\Моя прошивка\Key.bin PhatKey files extraction aborted! Drive is Lite-On.. Drive is Lite-On.. Sending Vendor Intro to port 0x01F0 Status 0x51 Re-sending Vendor Intro: ................. Serial flash found with Status 0x52 Extracted drive key passed Verification ! key returned: 1B824441DB78985D7369CCFE7BDE83B7 Key data saved to C:\Users\SVITCHER\Desktop\RatioMaster-1.9.1\Key.bin PhatKey files extraction aborted! No Drive Detected! DVDkey files extraction aborted! Drive is Lite-On.. Drive is Lite-On.. Drive is Lite-On.. Sending Vendor Intro to port 0x01F0 Status 0x51 Re-sending Vendor Intro: ............. Serial flash found with Status 0x52 Extracted drive key passed Verification ! key returned: 1B824441DB78985D7369CCFE7BDE83B7 Key data saved to C:\Users\SVITCHER\Desktop\RatioMaster-1.9.1\dummy.bin PhatKey files extraction aborted! No Drive Detected! DVDkey files extraction aborted! Drive is Lite-On.. Drive is Lite-On.. Sending Vendor Intro to port 0x01F0 Status 0x51 Re-sending Vendor Intro: ........................ Serial flash found with Status 0x52 Extracted drive key passed Verification ! key returned: 1B824441DB78985D7369CCFE7BDE83B7 Key data saved to C:\Users\SVITCHER\Desktop\RatioMaster-1.9.1\Key.bin 0000: 05 80 00 32 5B 00 00 00 - 50 4C 44 53 20 20 20 20 ...2[...PLDS 0010: 44 47 2D 31 36 44 32 53 - 20 20 20 20 20 20 20 20 DG-16D2S 0020: 30 32 35 31 30 43 41 30 - 41 30 44 36 30 38 43 47 02510CA0A0D608CG 0030: 37 33 38 38 30 38 30 30 - 33 34 38 20 20 20 00 00 73880800348 .. 0040: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 0050: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ Inquiry String saved to C:\Users\SVITCHER\Desktop\RatioMaster-1.9.1\Inquiry.bin 0000: 05 80 00 32 5B 00 00 00 - 50 4C 44 53 20 20 20 20 ...2[...PLDS 0010: 44 47 2D 31 36 44 32 53 - 20 20 20 20 20 20 20 20 DG-16D2S 0020: 30 32 35 31 30 43 20 20 - 00 00 00 00 00 00 00 00 02510C ........ 0030: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 0040: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 0050: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 0000: C0 85 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 0010: 00 00 00 00 44 36 30 38 - 43 47 37 33 38 38 30 38 ....D608CG738808 0020: 30 30 33 34 38 20 20 20 - 00 00 00 00 00 00 32 30 00348 ......20 0030: 31 35 43 30 20 20 4C 50 - 53 44 20 20 20 20 47 44 15C0 LPSD GD 0040: 31 2D 44 36 53 32 20 20 - 20 20 20 20 20 20 20 20 1-D6S2 0050: 20 20 20 20 20 20 20 20 - 20 20 20 20 20 20 00 00 .. 0060: 00 00 00 0B 00 00 00 04 - 00 02 06 00 00 00 00 00 ................ 0070: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 0080: 03 00 78 00 78 00 E3 00 - 78 00 00 00 00 00 00 00 ..x.x...x....... 0090: 00 00 00 00 00 00 00 00 - 02 02 00 00 68 00 00 00 ............h... 00A0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00B0: 20 20 00 00 .. Identify String saved to C:\Users\SVITCHER\Desktop\RatioMaster-1.9.1\Identify.bin 0000: 44 36 30 38 43 47 37 33 - 38 38 30 38 30 30 33 34 D608CG7388080034 0010: 38 20 20 20 FF FF FF FF - FF FF FF FF FF FF FF FF 8 ............ 0020: FF FF FF FF FF FF FF FF - 41 30 FF FF FF FF FF FF ........A0...... 0030: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ................ 0040: FF FF FF FF FF FF FF FF - FF FF FF FF 41 30 FF FF ............A0.. Serial String saved to C:\Users\SVITCHER\Desktop\RatioMaster-1.9.1\Serial.bin Dummy.bin file saved to dummy.bin Loading firmware from buffer Inquiry string found Identify string found Drive key @ 0xA030 1B824441DB78985D7369CCFE7BDE83B7 Firmware Osig: [PLDS DG-16D2S 0251] Firmware is: PhatKey Extract Key added to database Loading firmware file C:\Users\SVITCHER\Desktop\RatioMaster-1.9.1\dummy.bin MD5 hash: a71a19bcff55e856d66de0999ee5604f Inquiry string found Identify string found Drive key @ 0xA030 1B824441DB78985D7369CCFE7BDE83B7 Firmware Osig: [PLDS DG-16D2S 0251] Firmware is: PhatKey Extract Loading firmware file C:\Users\SVITCHER\Desktop\Новая папка (4)\firmware\LTPlus-lite-on-0251-v3.0.bin MD5 hash: d14fe82b96741b7a18e5c1e7adbf0a98 Genuine LT plus v3.0 Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF Firmware Osig: [PLDS DG-16D2S 0251] Firmware is: LT-Plus 3.0 Spoofing Target DVD Key copied to target Target is LT - ID strings not copied to Target Serial data already matches Target rev is LT 02510C, serial info not copied Target f/w saved as: Lite_CFW.bin Attempting to verify Target Key to drive on port 0x01F0 Key found in KeyDB at record (1 - RatioMaster-1.9.1) Key is: 1B824441DB78985D7369CCFE7BDE83B7 Key has been tested and verified, thanks C4eva ! Attempting to verify Target Key to drive on port 0x01F0 Key found in KeyDB at record (1 - RatioMaster-1.9.1) Key is: 1B824441DB78985D7369CCFE7BDE83B7 Key has been tested and verified, thanks C4eva ! Target f/w saved as: Lite_CFW.bin Attempting to verify Target Key to drive on port 0x01F0 Key found in KeyDB at record (1 - RatioMaster-1.9.1) Key is: 1B824441DB78985D7369CCFE7BDE83B7 Key has been tested and verified, thanks C4eva ! Sending Lite-On-Erase request to port 0x01F0 .............. Drive returned Status 0xD0 .................... Device Intro failed! Sending Lite-On-Erase request to port 0x01F0 .............. Drive returned Status 0x50 . Serial flash found with Status 0x72 Manufacturer ID: 0xC2 Device ID: 0x11 Flash Name: MXIC(MX25L2005) Flash Size: 262144 bytes Getting Status from port 0x01F0 SPi flash found with Status 0x72 Sending Chip Erase to Port 0x01F0 Erasing: Writing target buffer to flash Writing Bank 0: ................ Writing Bank 1: ................ Writing Bank 2: ................ Writing Bank 3: ................ Flash Verification Test ! Reading Bank 0: ................ Reading Bank 1: ................ Reading Bank 2: ................ Reading Bank 3: ................ Write verified OK ! Sending Vendor Outro to port 0x01F0 Drive is Lite-On.. Key found in KeyDB at record (1 - RatioMaster-1.9.1) Key is: 1B824441DB78985D7369CCFE7BDE83B7 Key has been tested and verified, thanks C4eva ! --- добавлено: Jan 23, 2012 2:56 PM --- Подключил обратно привод к консоли и теперь высвечивается ошибка E64.Я полностью убил приставку?)
Так) обратно подключил привод к компьютеру, выбрал порт - на котором раньше определялся привод. Нажал id Divice...и высветился объем флешь памяти и статус Вендор мод. обратно ввел все ключи, нажал write, потом Reset..и о чудо...вроде дошилось. подсоединил к приставке, приставка включилась, но диски по прежнему не видит. Даже не раскручивает диск.